RF anlyzar マイナーチェンジ
以前UPしたRFアナライザーを暫く使っていて、その使い勝手を良くするために少し改良を行った。【 改良点 】
photo 1 |
SGでDUTに信号を入力し出力を見たいことがあるが、以前はこの機能が別になっているので出来なかったが、今回SG機能にパワー計を入れ同時に使えるようにした。
この追加によりMENU2のパワー計は不要にも思うが、換算等の情報もあるため残してある。
[2] 表示レベル変更
Frequency Analyzerモード(以下FRAモード)、Antenna Analyzerモード(以下AAモード)でスケール以上、以下のレベルになった時表示が乱れることから、スケールの上限下限に制限するようにした。
[3] FRAモードでMAX,MINの測定
今までこの測定は測定スパンが200KHz以下だったのを300kHz以下とした。
[4] 表示リライトモード
FRA、AAモードはフリーランで上書きとなっているが、表示が醜くなることがあるため、UPスイッチを押すことにより画面をクリアし書き直すようにした。以前はメニューに戻って再度設定表示となり面倒であった為である。
[5] EEPROMリセット
稀にEEPROMを初期設定値に戻したいことがあったため、enterスイッチを押しながら電源ONにするとEEPROMを初期化することが出来るようにした。
今までこの測定は測定スパンが200KHz以下だったのを300kHz以下とした。
[4] 表示リライトモード
[5] EEPROMリセット
稀にEEPROMを初期設定値に戻したいことがあったため、enterスイッチを押しながら電源ONにするとEEPROMを初期化することが出来るようにした。
今回の改良でハードウェアは変更していない。
Ver1.06にバグがあったのでVer1.07にしました。
Ver1.06にバグがあったのでVer1.07にしました。
スケッチはダウンロードサイトにアップしてある。
RF Analyzer is minor changed.
- Added Power meter on Signal Generator mode. (photo 1)
Although I sometimes want to input the signal to the DUT by SG and wish to see the output. I could not do it because this function was separate in the past, but this time I added a power meter in the SG function and can use it at the same time. Thanks to this addition, I think the power meter of MENU 2 is unnecessary, but because there is information such as conversion, it is left behind. - Display of FRA mode & AA mode over level limit set upper & lower line.
In the frequency analyzer mode (hereinafter referred to as FRA mode) and the Antenna Analyzer mode (hereinafter referred to as AA mode) the display is disturbed when it reaches or exceeds the scale level, so it is limited to the upper limit line and the lower limit line of the scale. - Max & Min value measurement of FRA mode
Max & Min value measurement of FRA mode operates when the span is 300kHz or less. The previous version was less than 200kHz - Added rewite mode.
Pressing UP_switch while displaying FRA & AA mode will rewrite it. - EEPROM Reset
Hold down ENTER_switch and turn on the power to reset EEPROM.
Hardware has not been changed by this improvement.
There was a bug in Ver1.06, I made it to Ver1.07
There was a bug in Ver1.06, I made it to Ver1.07
The sketch has been uploaded to the my download site.
Let's enjoy homebrew.
73's JA2ND Ryuu
早速互換nanoでこんなパイルしてみましたがコンパイルエラーが出ました
返信削除後日添付ファイルでおりますのでアドバイスお願いします。nanoは互換品で簡単なスケッチで動作確認しましたがこれを使うのは初めてです
環境はwin7pro64 ide1.8.3 usb
原田さん
返信削除エラーメッセージの内容をお知らせください。
Hi
返信削除How about using a ad9851 module?
返信削除Hi,PP2KR
Thanks comments.
This Analyzer is using AD9850 DDS module.
Of course it's possible to use AD9851 DDS,too.
But it's need to fix the sketch a little.
Let's enjoy homebrew.
Thank you
73's JA2NKD
Bagus sekali karyanya. Saya jadi ingin membuatnya. Sukses selalu
返信削除Hi,Azzam
返信削除Thank you for having interest in my blog.
Let's enjoy homebrew.
73's
JA2NKD Ryuu
Hello
返信削除From where I can get the PCB layout for this project..
Please share with me the layout file with me
73
Ameer Khan VU3SQM
vu3sqm at Gmail for com
Hi,Ameer(VU3SQM)
返信削除Thank you comment.
Sorry I maid using universal PCB.
My Friend made PCB.
http://soltec.exblog.jp/27990546/
Please contact him.
Let's enjoy homebrew.
73's
JA2NKD Ryuu
Hi,
返信削除Can I have the sketch for 9851. I have 9851 available.
Ameer, please contact vu2upx for the pcb. He gave me two pc today in hamfest meet.
Thanks
De vu3cav
Rajani Mohan
VU3CAV@GMAIL.COM
Hi,Rajani
返信削除Using 9851 with the same specification is easy. However, in order to derive the performance of 9851 a little hardware change is necessary.
I have not done the exam yet.
I think I will do it when I can do the time.
>Ameer, please contact vu2upx for the pcb. He gave me two pc today in hamfest meet.
???? Sorry I can not understand.
It is not good manners to put an email address in comments.
I think that it is better to be aware.
73's
JA2NKD Ryuu
Hi Ryuu,
返信削除Thanks for your advice on not mentioning the email id. I am sorry as I was not aware of it. Will take care
Ameer Khan had asked for layout in this discussion thread I have suggested to get in contact with OM charu vu2upx for the same.
Can we use same sketch for 9851
Thankx
Rajani
Hi,Rajani
返信削除Sorry I can not understand the following sentences.
>Ameer Khan had asked for layout in this discussion thread I have suggested to get in contact with OM charu vu2upx for the same.
>Can we use same sketch for 9851
Please write me easily what you want me to do?
JA2NKD Ryuu
can you share scheme of antena bridge for antena analyzer menu? thanks a lot
返信削除このコメントは投稿者によって削除されました。
返信削除I wanted to know if this project http://www.ur5ffr.com/viewtopic.php?f=25&t=198&sid=377f75a9071191c66cea44e4d2f404ff could be ported to Raspberry Pi PICO with a TFT display and a web interface in the W version
返信削除